{"id":161,"date":"2021-09-29T10:57:57","date_gmt":"2021-09-29T10:57:57","guid":{"rendered":"https:\/\/sznetwork.systems\/?page_id=161"},"modified":"2021-10-18T05:24:59","modified_gmt":"2021-10-18T05:24:59","slug":"sz_io62r2","status":"publish","type":"page","link":"https:\/\/sznetwork.systems\/?page_id=161","title":{"rendered":"SZ_IO62R2"},"content":{"rendered":"\n

SZ_IO62R2<\/h2>\n\n\n\n

Page created: 28\/09\/2021<\/strong> Updated: 18\/10\/2021 <\/strong><\/p>\n\n\n\n

\n
\n
\"\"<\/figure>\n<\/div>\n\n\n\n
\n

SZ_IO62R2 is second code revision of SZ_IO62 controller. Have many improvements over SZ_IO controller.For example, now we can control same outputs from separate inputs. All detail information will be below.<\/p>\n<\/div>\n<\/div>\n\n\n\n

Features<\/strong>\n\n- Support remotely (RS-232) turning on or off added devices\n- Support single or toggle input.  \n- Supports turning on or off up to 8 separately connected devices\n-  Configuration over RS-232.\n-  Multiply control outputs from separate outputs (added in SZ_IO62R2)\n-  On start controller send to terminal current configuration in one string separated by semicolon.\n-  On start controller send to terminal status of inputs and outputs\n-  Controller have 6 hardware inputs and 2 additional software inputs\n-  Support input output status checking by command via terminal\n-  Support controlling outputs independently of inputs by separate command \"outX\"<\/pre>\n\n\n\n
Functions<\/strong>\n\n- After controller restart last state only for switch mode\n- Allows to control 8 outputs from 6 separate hardware inputs, or from serial port.\n- Allows to control 8 outputs from 2 virtual inputs independently of hardware inputs\n- Can be integrated Home Assistance or another system throw serial port\n- Hardware inputs have two functions single click or toggle\n- On start controller outputs is HIGH (+5 Volt 25 mA), then output is active it is LOW (0 Volt)<\/pre>\n\n\n\n
Parameters<\/strong>\n\n- Package Included: 1pc SZ\\_IO\\_62R2 Module  \n- Size: 6.5 x 7.1 x 2.5 mm (HxWxD)  \n- Work Voltage: DC 5-12v correct  \n- Work Current: 25 mA (standby)  \n- Load Voltage: 5V  \n- Load Current: 25mA\/Channel(MAX)  \n- Output Type: Discrete  \n- Control Mode: Physical switch (button), RS-232  \n- Communication: RS-232, band rate 115200<\/pre>\n\n\n\n
Work modes<\/strong>\n\n- Hardware click - one click to turn on or off configured outputs    \n- Hardware toggle - if input is shorted, opened to ground then turn on or off configured outputs  \n\n RS-232 commands:  \n-  cI1 - same as hardware click only emulated from console. \n-  sI1 - same as hardware toggle ON\/OFF only emulated from console. \n-  out1 - independent output control\n-  stat - get status of hardware inputs and outputs\n-  rconf - get configuration in one string separated by semicolon.<\/pre>\n\n\n\n
Commands<\/strong>\n\nTo use hardware buttons\/switches just connect button\/switch to input and load to output. Program input working mode and assign outputs. After all done, just push button\/switch.  \nSerial commands use RS-232 terminal:  \nsIX<\/strong> - turn on input X (where X is input number), if all ok you will see reply with status op inputs and outputs. \ncIX<\/strong> - turn on\/off single click input X (where X is input number), if all ok you will see reply with status op inputs and outputs. \noutX<\/strong> - turn on\/off output X (where X is input number), if all ok you will see reply with status op inputs and outputs.\nstat<\/strong> - show status of inputs and outputs\nconf<\/strong> - list all configured inputs  <\/pre>\n\n\n\n
Reset to default<\/strong>\n\nReset from terminal:  \nD0S1 1<\/strong> - will reset to default configuration.  \nsave<\/strong> - saves the config and reboots controller  <\/pre>\n\n\n\n
\n
\n
Connection scheme\n<\/strong><\/pre>\n\n\n\n
\"szio62connection\"<\/figure>\n<\/div>\n<\/div>\n\n\n\n